Gradall 544D (9136-4003) Service Manual User Manual download pdf (Page 295)

ASSEMBLY OF POWER WHEEL

STEP 1

Press new bearing cups (7 & 10) in each side of the hub (9). It is recommended that bearing

cups (7 & 10) and cones (6 & 11) be replaced in sets.

STEP 2

Assemble bearing cone (6) into cup (7) at seal end of hub (9) and press a new seal (5) into hub

(9). Install boot seal (4) on hub (9) if unit is so equipped.

STEP 3

Position spindle (3) upright on bench. Lubricate lips of seals (4) and (5) and lower hub (9) onto

spindle (3). Hub (9) shouid be centered as it is lowered over spindle (3) to prevent seal damage.

STEP 4

Assemble bearing cone (11) over spindle end. Press bearing cone (11) over spindle bearing

journal using press and cylindrical bearing tool AG08404B. Press bearing cone (11) down until

roller just touches cup (10). (OPTIONAL: Use hammer and bearing tool AG08404B to install cup

(11) over spindle (3). Take care when using this method to avoid pressing cone (11) too far. As

in other method, rollers should just touch cup (10)).

STEP 5

Install thrust washer (12) and bearing nut (14). DO NOT install lockwasher (13) at this time.

STEP 6

Place rolling torque tool AG08771C over spindle (3) and bolt or pin to hub (9).STEP 7

Check initial rolling torque by installing an inch-lb. torque wrench on center nut of rolling torque

tool and turning hub (9) slowly and steadily with the torque wrench. Note mean torque. An initial

bearing rolling torque of greater than 52 in-lbs. means that the cone (11) was pressed on too

tightly in step 4. In this case, back off bearing cone (11) by pressing spindle (3) out of cone (11)

until initial preload is relieved.

STEP 8

Torque bearing nut (14) with bearing nut wrench AG07366B until a bearing rolling torque of 44-52

in-lbs., with a boot seal installed, or 4048 in-lbs., without a boot seal, is reached. This may

require several trials of pressing the cone (11) by torqueing the nut (14) and then checking the

rolling torque. Rotate hub (9) by hand as nut is being tightened in order to seat bearings. NOTE:

Up to 250 ft-lbs. of torque may have to be applied to bearing nut (14) in order to press cone (11)

into position.

STEP 9

Remove bearing nut (14) and install lockwasher (13). Install nut (14).

STEP 10

Re-torque bearing nut (14) to 65-75 ft-lbs.

STEP 11

Secure bearing nut (14) by bending a lockwasher (13) tab into one of four bearing nut slots. If no

tab aligns with a slot, the nut may be tightened until one of the slots aligns with a lock washer tab.

STEP 12

Assemble a washer (16), spring (17), a second washer (16), and a retaining ring (15) in the middle

grooves of input shaft (2). Install a second retaining ring (15) in groove near small end of input

shaft (2).

STEP 13

Assemble the splined end of the input shaft (2) down into spindle (3).

STEP 14

Assemble the secondary carrier assembly (19) to spindle (3) at splines.

STEP 15

Clean mating surfaces and apply a bead of silicone sealant to face of hub (9) that mates with ring

gear (18). (See instructions on sealant package). Assemble ring gear (18) to hub (9) being

careful to align bolt holes.

STEP 16

Assemble the primary carrier assembly (20) into the ring gear (18). It will be necessary to rotate

carrier to align secondary sun gear (part of primary carrier assembly (20)) with planet gear teeth in

secondary carrier assembly (19). Assemble primary sun gear (21) over input shaft (2). Rotate

primary sun gear (21) to align input shaft (2) to gear splines and gear teeth in primary carrier

assembly (20).

STEP 17

Lubricate O-ring (24) and assemble in groove inside cover hole, push disengage plunger (23) into

cover (25) with pointed end facing inside of unit.

1 2 ... 290 291 292 293 294 295 296 297 298 299 300 ... 391 392

Comments to this Manuals

No comments

Gradall 544D (9136-4003) Service Manual User Manual Page 295

Comments to this Manuals

Related products and manuals for Hoist Gradall 544D (9136-4003) Service Manual